Creative Effects Application

Coverage: All Colors - 1L / 200 sq ft.

Precolor Easy

Furniture and stairs 

  1. Sand the surface scratch-free. Finish with screening net 100 to 150, the color intensity depends on the sanding method used. 
    • When renovating, you must remove all the residues from previous treatments completely (varnish, oil, wax, etc.). 
  2. Vacuum thoroughly and eliminate remains of dust with Rubio Monocoat Cleaner. Wait until the surface is completely dry
    (check the technical datasheet of the Cleaner before use). 
  3. Stir the product thoroughly and regularly with a stirring stick. 
  4. Apply an amount of Rubio Monocoat Precolor Easy with the Rubio Monocoat Brush and spread out using a red Rubio Monocoat Scrubby Pad. Wipe out evenly with a lint-free cloth. Work in small areas to avoid overlapping.
    • For smaller objects and corners you can also use the green Rubio Monocoat Mouse Pad. 
  5. Allow the surface to dry for ± 12 hours. The exact drying time depends on the foundation, moistening, temperature and ventilation. 
  6. After drying, break the raised wood fibers with a red Scrubby Pad and vacuum afterwards. 
  7. Now apply the Rubio Monocoat Oil Plus 2C. Please consult the technical data sheet of the oil for a correct application. Be careful, in combination with Precolor Easy it is best to use a white Scrubby Pad instead of a beige or red one when applying the oil.

Floors 

  1. Sand the surface scratch-free. Finish with screening net 100, the color intensity depends on the sanding method used. 
    • When renovating, you must remove all the residues from previous treatments completely (varnish, oil, wax, etc.). 
  2. Vacuum thoroughly and eliminate remains of dust with Rubio Monocoat Cleaner. Wait until the surface is completely dry
    (check the technical datasheet of the Cleaner before use). 
  3. Tape off areas of ± 90 cm, in the lengthwise direction of the boards. 
  4. Stir the product thoroughly and regularly with a stirring stick. 
  5. Apply the Rubio Monocoat Precolor Easy with a Rubio Monocoat Microfiber Pad. Make sure to use enough of the product and cover the whole area. Afterwards smooth out the area again with the same Microfiber Pad. Make sure that this pad is thoroughly wrung out. 
  6. Now skip an area and follow the instructions in step 5 again for this next area. Finish the whole room in this way and remove the tape. Allow the surface to dry for ± 12 hours. 
  7. Now tape off the untreated areas and apply the Precolor Easy as described in step 5. Repeat until the whole floor is treated. Afterwards remove the tape
    (tip: step on the already dried-out areas to remove the tape). 
  8. Allow the surface to dry for ± 12 hours. The exact drying time depends on the foundation, moistening, temperature and ventilation. 
  9. After drying, break the raised wood fibers with a floor polisher equipped with a red Rubio Monocoat Pad and vacuum afterwards. 
  10. Now apply the Rubio Monocoat Oil Plus 2C. Please consult the technical data sheet of the oil for a correct application. Be careful, in combination with Precolor Easy it is best to use a white Pad instead of a beige or red one when applying the oil! 

Tips & Tricks

  •  Stir the product well before application. 
  • When using several containers at one site, it is required to mix them for an even result. 
  • Switch off the floor heating 48 hours before application. 
  • Do not use in combination with water-based finishing products, such as Rubio Invisible Protector. 
  • Difficult to apply on herringbone parquet. 
  • Keep in mind that the wood type, grain structure and porosity of the wood can influence the end result. Therefore, it is important to make a sample first on the chosen wood species or the surface that needs treating.  

Precolor Easy Application Instructions and TDS Download (EN)

Precolor Easy Application Instructions and TDS Download (ES)

 

Rubio Fumed

Manual Application

  1. Sand the planks until the desired effect has reached.- Remove any dust.
  2. Apply RMC Fumed regularly using a roller or a brush. If a smooth effect is required saturate the surface completely with the product.
  3. Let the surface dry completely (12 to 48 hours).
  4. Sand the surface lightly with a polisher equipped with a beige pad.
  5. Remove any dust again.
  6. Finish with Rubio Monocoat Oil

Consumption
Depending on type of wood and preparation:  +/- 215 to 430 g/sq. ft. 

These usages are merely indicative. Results depend on wood type and method of preparation. It is always recommended to make a sample in order to calculate the exact usage.  

Application Instructions and TDS (EN)

Application Instructions and TDS (ES)

 

Rubio Smoke

Manual Application

  1. Sand the planks until the desired effect is reached.
  2. Remove any dust.
  3. Apply RMC Smoke regularly using a roller or a brush. If a smooth effect is required saturate the surface completely with the product.
  4. Wash off the excess product with water and a sponge, go over the surface and wring the sponge with the absorbed product out in the second bucket.
  5. Let the surface dry completely (12 to 48 hours).
  6. Sandpaper the surface lightly with a polisher equipped with a beige pad.
  7. Remove any dust again.
  8. Finish with Rubio Monocoat Oil.

Consumption
Depending on type of wood and preparation:  +/- 215 to 430 g/sq. ft. 

These usages are merely indicative. Results depend on wood type and method of preparation. It is always recommended to make a sample in order to calculate the exact usage. 

Application Instructions and TDS (EN)

Application Instructions and TDS (ES)

 

This site uses cookies to ensure that we give you the best experience on our website.