In stock
Out stock


Rubio Monocoat SheenPlus


To be used after finishing with Oil Plus 2C

Rubio Monocoat SheenPlus is a 0% VOC sheen enhancer that provides a durable satin look to wooden surfaces that have been finished with Rubio Monocoat Oil Plus 2C wood finish. This product may be applied on all indoor wood surfaces, including furniture, countertops, tables, stairs, walls, floors, etc., finished with Oil Plus 2C. The combination of the oil (A) and accelerator (B) ensures a fast cure time, resulting in excellent protection. Plus, it's solvent and water-free.

130 ML
350 ML
1.3 L
Spend $79.00 to Free Shipping
  • Durable satin look
  • Environmentally friendly with 0% VOC
  • Scratch-resistant result
  • No overlapping
  • High spread rate
  • To be applied by hand, or using a floor buffer outfitted with a pad
  • 100% solid content


An overview of instructions. Please consult the TDS for complete product information.

Application on furniture and tables

  1. Let the Oil Plus 2C dry for at least 24 - 36 hours.
  2. Thoroughly mix the two SheenPlus components together for 1 to 2 minutes, ensuring a ratio of approximately 3 units A to 1 unit B.
  3. Apply a small amount of SheenPlus with a brush and spread further with a red Scrubby Pad. Within 15 minutes, go over the same surface again with the red Scrubby Pad without adding additional product.
  4. Wipe again with a white Scrubby Pad.
  5. Remove any streaks and/or surface irregularities with a lint-free cloth.
  6. Let dry for at least 24 hours before light use of the surface. To ensure effective drying and curing, it is important to maintain proper ventilation and temperature. Full curing takes place in 7 days.

Application on floors

  1. Let the Oil Plus 2C dry for at least 24 - 36 hours.
  2. Thoroughly mix the two SheenPlus components together for 1 to 2 minutes, maintaining a ratio of approximately 3 units A to 1 unit B.
  3. Apply a small amount of SheenPlus using a floor buffer with a red buffer pad. Spread the product to ensure no irregularities are visible in the treated area. Optimal treatment areas are between 20 to 40 square feet, avoiding excessively wide spaces. Ensure that the floor buffer can be maneuvered easily without stepping into the wet product.
    TIP: If the layout of the area being treated does not allow you to work without standing in the still wet product, use (half) a white pad to stand on during application.
  4. Within 15 minutes, complete the treatment for the area using a white buffer pad until the surface becomes uniformly even and dries to a rub-off finish. Use a lint-free cloth to remove any streaks or irregularities in the surface.
  5. Repeat these treatment steps across the entire surface in segments that can be treated within a 15-minute timeframe.
  6. Allow the treated surface to dry for a minimum of 24 hours before cautiously walking on it. To ensure effective drying and curing, maintain proper ventilation and temperature. Full curing will occur over a period of 7 days.


If the product starts to show too much wear (traffic pattern), you can easily solve this by applying a new coat. First, make sure to remove any dust and dirt prior to applying a maintenance coat. Refer to the steps on pages 2-3 for the proper cleaning and application instructions.

When Oil Plus 2C color wear is evident, first perform a repair/renovation with the original Oil Plus 2C color (Part A & B must be used for the color restoration). After that, let dry for at least 24 - 36 hours. Then, apply SheenPlus to the repaired area and let it dry for 24 hours. After that, apply SheenPlus to the entire floor surface.

SheenPlus TDS (EN)
SheenPlus Leaflet (EN)


Summarized specifications, please read TDS before using product.

Spread Rate: 1000-1600 ft²/L
Spread Rate By Packaging:
130 ml = 130-208 ft²
350 ml = 350-560 ft²
1.3 liter = 1300-2080 ft²
Cure Time: 7 days
VOC Content: 0%
Color Options: 5
Dilutable: No
Shelf Life: 36 months
Dry Time: Varies. Test with a moisture meter before and after to ensure full dry.

Warning: Do not allow to freeze
Combustion Warning: Cloths, saturated with oil, may spontaneously combust. After usage, they need to be soaked in water before disposal.


Can SheenPlus be applied on raw wood?

No. SheenPlus must be applied over Oil Plus 2C.

Can SheenPlus be applied over Universal Maintenance Oil or Refresh Eco?

Yes. If there is damage or inconsistencies in the Oil Plus 2C or below the Oil Plus 2C, then SheenPlus will not fix the issue, and it is advisable to perform a renovation using Oil Plus 2C in the original color prior to applying SheenPlus.

Will applying multiple layers of SheenPlus increase the sheen level?

No. SheenPlus is a Monocoat product and only requires 1 single application. Adding another application of SheenPlus will not increase the sheen further.

How soon can I apply SheenPlus after Oil Plus 2C has been applied?

SheenPlus can be applied 24 hours after application of Oil Plus 2C.

Can I use SheenPlus Part A only?

No. It is mandatory to use SheenPlus Part A and Part B together.

This site uses cookies to ensure that we give you the best experience on our website.

Rubio Monocoat SheenPlus

Rubio Monocoat SheenPlus